ELEMENT 006 / NONMETAL
6CATOMIC NUMBER · SYMBOL

Carbon

Experimental chemistry • properties • laboratory science

Diamond, graphite, graphene, amorphous carbon and nanotubes differ drastically in bonding and properties.

Atomic no. 6NonmetalSolid at room conditions
Explore profile
IMAGE PLACEHOLDERCReal element images to be added later

Click a photograph for a larger view. Images are managed in the editor.

01
The essentials

Overview & practical chemistry

Identity, occurrence, applications and measurement context from the working reference manuscript.

Atomic number6
Symbol / typeC · Nonmetal • Solid at room temperature • atomic mass: 12.011 (rounded)
Elemental formSolid | selected oxidation states -4,+2,+4
Chemical identityDiamond, graphite, graphene, amorphous carbon and nanotubes differ drastically in bonding and properties.
Occurrence and productionCoal, hydrocarbons, biomass; high-purity graphite and synthetic diamond produced industrially.
Useful applicationsSteelmaking, electrodes, filters, structural composites and semiconductor diamond.
Analytical characterizationRaman spectroscopy for allotropes/defects; combustion analysis for carbon content.
Research / quality noteNever infer properties from 'carbon' alone: allotrope, morphology and defects control performance.
Oxidation and chemical formsSelected: -4 / +2 / +4. Values depend on compound and chemical environment.

Phase transitions & temperature reference

Elemental bulk · approximately 1 atm

At approximately 1 atm, bulk values depend on specimen, isotope mixture and phase. When specific measurements or published theoretical estimates exist, they are labeled. A value borrowed from a normal element is only a reference proxy. Plasma is an ionized state, without a single universal onset temperature.

Phase at 20 °C, ~1 atmSolid
Elemental-bulk melting / freezing (near 1 atm)Not applicable near 1 atm — graphite sublimes; high-pressure melting is separate
Elemental-bulk boiling / gas formation (near 1 atm)?
Sublimation (solid → gas) near 1 atm?
Additional solid–solid transitions?
Plasma onset temperatureNot a single phase boundary; ionization is density/pressure/energy dependent
Measurement conditionsca. 1 atm; evaluated elemental-bulk reference only
Data qualificationCarbon sublimes near ambient pressure; no ordinary 1-atm melting point. High-pressure melting is form-dependent.

Solid-phase reference: NIST Technical Note 2312 (2025). Boiling data: PubChem (NIH) where checked, otherwise secondary tabulation (provisional). Additional tabulated elemental values were cross-checked with the Royal Society of Chemistry. Where one exists, the named-form reference is not a universally applicable transition. Values can be form-dependent, metastable, estimated or pressure-dependent; verify against original reports for laboratory use.

02
Structure matters

Allotropes & elemental forms

Values are distinguished as form-specific measurements, theoretical predictions, or ELEMENTAL REFERENCE proxies. A numerical proxy describes the natural-element reference, not a measured melting/boiling point of that named form. ? remains where no defensible value or proxy exists.

Form / phaseState at 20 °CMelting / transitionBoiling / sublimation
Graphite (hexagonal and rhombohedral stacking)Solid / structural form; stability and sample dependentNot defined at ~1 atm for this structural form; graphite has no ordinary-pressure melting pointGraphite stable to at least ~4000 K (NIST standard-state discussion); NOT a sublimation point
Full record, evidence, conditions & photographs
Structure, conditions & interpretation
sp2-bonded sheets; different layer stacking sequences are documented. LAB: Conductive in-plane; compare XRD, Raman D/G/2D bands and stacking disorder.
Approximate solid / liquid / gas ranges
No universally defined normal-pressure melt; high-temperature vaporization/sublimation and allotrope transformations depend on conditions.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Phase conditions
Pressure and thermal history required; phase at 20 °C does not imply the named polymorph is stable
Evidence level
No universal form-specific bulk melting point; high-T reference only
Phase data source
https://trc.nist.gov/TDE/Help/TDE103b/The_Navigation_Tree/Navigation_Tree_%28Pures%29/Properties-of-Elements.htm
Photographs

No photograph added yet.

Diamond (cubic)Solid / structural form; stability and sample dependentNot defined at ~1 atm for this structural form; graphite has no ordinary-pressure melting pointGraphite stable to at least ~4000 K (NIST standard-state discussion); NOT a sublimation point
Full record, evidence, conditions & photographs
Structure, conditions & interpretation
Three-dimensional sp3 framework. LAB: Very hard and electrically insulating in pure form; Raman/XRD distinguish from graphite.
Approximate solid / liquid / gas ranges
No universally defined normal-pressure melt; high-temperature vaporization/sublimation and allotrope transformations depend on conditions.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Phase conditions
Pressure and thermal history required; phase at 20 °C does not imply the named polymorph is stable
Evidence level
No universal form-specific bulk melting point; high-T reference only
Phase data source
https://trc.nist.gov/TDE/Help/TDE103b/The_Navigation_Tree/Navigation_Tree_%28Pures%29/Properties-of-Elements.htm
Photographs

No photograph added yet.

Hexagonal diamond / lonsdaleite-type structuresSolid / structural form; stability and sample dependentNot defined at ~1 atm for this structural form; graphite has no ordinary-pressure melting pointGraphite stable to at least ~4000 K (NIST standard-state discussion); NOT a sublimation point
Full record, evidence, conditions & photographs
Structure, conditions & interpretation
Hexagonal sp3 stacking reported; distinguishing a discrete phase from heavily faulted cubic diamond remains an important identification issue. LAB: Do not label any defect-rich diamond as confirmed pure lonsdaleite without structural proof.
Approximate solid / liquid / gas ranges
No universally defined normal-pressure melt; high-temperature vaporization/sublimation and allotrope transformations depend on conditions.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Phase conditions
Pressure and thermal history required; phase at 20 °C does not imply the named polymorph is stable
Evidence level
No universal form-specific bulk melting point; high-T reference only
Phase data source
https://trc.nist.gov/TDE/Help/TDE103b/The_Navigation_Tree/Navigation_Tree_%28Pures%29/Properties-of-Elements.htm
Photographs

No photograph added yet.

GrapheneSolid / structural form; stability and sample dependentNot defined at ~1 atm for this structural form; graphite has no ordinary-pressure melting pointGraphite stable to at least ~4000 K (NIST standard-state discussion); NOT a sublimation point
Full record, evidence, conditions & photographs
Structure, conditions & interpretation
One-atom-thick sp2 carbon sheet. LAB: Thickness, layer count, substrate and defects matter; not identical to bulk graphite.
Approximate solid / liquid / gas ranges
No universally defined normal-pressure melt; high-temperature vaporization/sublimation and allotrope transformations depend on conditions.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Phase conditions
Pressure and thermal history required; phase at 20 °C does not imply the named polymorph is stable
Evidence level
No universal form-specific bulk melting point; high-T reference only
Phase data source
https://trc.nist.gov/TDE/Help/TDE103b/The_Navigation_Tree/Navigation_Tree_%28Pures%29/Properties-of-Elements.htm
Photographs

No photograph added yet.

Fullerenes (C60, C70, larger families)Solid / structural form; stability and sample dependentNot defined at ~1 atm for this structural form; graphite has no ordinary-pressure melting pointGraphite stable to at least ~4000 K (NIST standard-state discussion); NOT a sublimation point
Full record, evidence, conditions & photographs
Structure, conditions & interpretation
Discrete closed-cage molecular carbon species; many distinct cages and sizes. LAB: Mass spectrometry identifies cage composition; crystalline C60 is not a new elemental formula.
Approximate solid / liquid / gas ranges
No universally defined normal-pressure melt; high-temperature vaporization/sublimation and allotrope transformations depend on conditions.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Phase conditions
Pressure and thermal history required; phase at 20 °C does not imply the named polymorph is stable
Evidence level
No universal form-specific bulk melting point; high-T reference only
Phase data source
https://trc.nist.gov/TDE/Help/TDE103b/The_Navigation_Tree/Navigation_Tree_%28Pures%29/Properties-of-Elements.htm
Photographs

No photograph added yet.

Carbon nanotubesSolid / structural form; stability and sample dependentNot defined at ~1 atm for this structural form; graphite has no ordinary-pressure melting pointGraphite stable to at least ~4000 K (NIST standard-state discussion); NOT a sublimation point
Full record, evidence, conditions & photographs
Structure, conditions & interpretation
Rolled sp2 frameworks; single- and multi-walled, varied chirality. LAB: Raman/TEM distinguish nanotube class, diameter and defects.
Approximate solid / liquid / gas ranges
No universally defined normal-pressure melt; high-temperature vaporization/sublimation and allotrope transformations depend on conditions.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Phase conditions
Pressure and thermal history required; phase at 20 °C does not imply the named polymorph is stable
Evidence level
No universal form-specific bulk melting point; high-T reference only
Phase data source
https://trc.nist.gov/TDE/Help/TDE103b/The_Navigation_Tree/Navigation_Tree_%28Pures%29/Properties-of-Elements.htm
Photographs

No photograph added yet.

Carbyne / linear carbon chainsSolid / structural form; stability and sample dependentNot defined at ~1 atm for this structural form; graphite has no ordinary-pressure melting pointGraphite stable to at least ~4000 K (NIST standard-state discussion); NOT a sublimation point
Full record, evidence, conditions & photographs
Structure, conditions & interpretation
sp-bonded carbon chains can be stabilized under specialized conditions; bulk free-standing existence and persistence are limited. LAB: Distinguish experiments from theoretical infinite chains.
Approximate solid / liquid / gas ranges
No universally defined normal-pressure melt; high-temperature vaporization/sublimation and allotrope transformations depend on conditions.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Phase conditions
Pressure and thermal history required; phase at 20 °C does not imply the named polymorph is stable
Evidence level
No universal form-specific bulk melting point; high-T reference only
Phase data source
https://trc.nist.gov/TDE/Help/TDE103b/The_Navigation_Tree/Navigation_Tree_%28Pures%29/Properties-of-Elements.htm
Photographs

No photograph added yet.

Amorphous/glassy/disordered carbon and carbon nanofoamsSolid / structural form; stability and sample dependentNot defined at ~1 atm for this structural form; graphite has no ordinary-pressure melting pointGraphite stable to at least ~4000 K (NIST standard-state discussion); NOT a sublimation point
Full record, evidence, conditions & photographs
Structure, conditions & interpretation
Broad structural families rather than one well-defined single allotrope. LAB: Specify sp2/sp3 fraction, porosity, Raman spectra and impurities; avoid unqualified “one amorphous allotrope.” [AL2,AL4,AL17]
Approximate solid / liquid / gas ranges
No universally defined normal-pressure melt; high-temperature vaporization/sublimation and allotrope transformations depend on conditions.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Phase conditions
Pressure and thermal history required; phase at 20 °C does not imply the named polymorph is stable
Evidence level
No universal form-specific bulk melting point; high-T reference only
Phase data source
https://trc.nist.gov/TDE/Help/TDE103b/The_Navigation_Tree/Navigation_Tree_%28Pures%29/Properties-of-Elements.htm
Photographs

No photograph added yet.

Identification and structural context
Named forms noted in chapterDiamond, graphite, graphene, amorphous carbon and nanotubes differ drastically in bonding and properties.
OverviewAllotropy describes structurally different forms made of the same element. Distinguish genuine allotropes from melting/freezing, impurities, compounds, isotopes, size-dependent surface effects and magnetic transitions. “Normal” below means approximately 1 atm unless another pressure is stated.
Transition noteNo additional independently evaluated ordinary-pressure solid–solid transition temperature is listed here. Absence of a table entry does not prove that no pressure-induced or metastable phases exist.
Laboratory identificationLaboratory identification: use phase-specific powder/single-crystal XRD, Raman or other appropriate spectroscopy, with documented temperature, pressure, composition, impurities, substrate and thermal history. A color or appearance alone is insufficient.
Evidence & scopeEvidence & scope: [AL2, AL4, AL10, AL17]. Lists cover established principal named forms and notable experimentally reported polymorphs; an absolutely exhaustive list of all high-pressure, ultrathin, transient, metastable or newly discovered structures is not scientifically fixed. If data are unavailable, this is recorded rather than invented.
03
Nuclear science

Selected isotopes & radioactivity

This is a selected isotope list, not all known nuclides. Exact isotope-specific results are used where documented; elsewhere numerical elemental references are shown only as proxies, never as measurements or calculated isotope-specific estimates. Very short-lived isotopes cannot practically be collected in bulk. Plasma has no universal onset temperature.

NuclideHalf-lifeState at 20 °CMelting / transitionBoiling / sublimation
C-12Stable; no observed radioactive decaySolid (expected elemental chemical form, not isotope-specific observation)??
Full record, evidence, conditions & photographs
Decay or evidence note
Stable nuclide; verify current NNDC evaluation
Approximate solid / liquid / gas ranges
No universally defined normal-pressure melt; high-temperature vaporization/sublimation and allotrope transformations depend on conditions.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Pressure / sample conditions
Pure isotope values can differ from natural-element mixture; ~1 atm reference; the elemental form and isotopic enrichment must be specified.
Evidence level
Not determined for this isotope
Isotope phase source
?
Photographs

No photograph added yet.

C-13Stable; no observed radioactive decaySolid (expected elemental chemical form, not isotope-specific observation)??
Full record, evidence, conditions & photographs
Decay or evidence note
Stable nuclide; verify current NNDC evaluation
Approximate solid / liquid / gas ranges
No universally defined normal-pressure melt; high-temperature vaporization/sublimation and allotrope transformations depend on conditions.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Pressure / sample conditions
Pure isotope values can differ from natural-element mixture; ~1 atm reference; the elemental form and isotopic enrichment must be specified.
Evidence level
Not determined for this isotope
Isotope phase source
?
Photographs

No photograph added yet.

C-145,730 ySolid (expected elemental chemical form, not isotope-specific observation)??
Full record, evidence, conditions & photographs
Decay or evidence note
beta-
Approximate solid / liquid / gas ranges
No universally defined normal-pressure melt; high-temperature vaporization/sublimation and allotrope transformations depend on conditions.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Pressure / sample conditions
Pure isotope values can differ from natural-element mixture; ~1 atm reference; the elemental form and isotopic enrichment must be specified.
Evidence level
Not determined for this isotope
Isotope phase source
?
Photographs

No photograph added yet.

Radiological exposure & interpretation
Isotope basisNaturally occurring material may contain low-activity radionuclide(s); example C-14. Many laboratory-enriched/activated forms are different.
External radiation — near-termTypical small natural-composition samples are not expected to cause prompt external radiation injury; this is NOT a clearance for concentrated or activated material. Specific example: C-14 is a low-energy beta emitter; usually limited external skin penetration.
External radiation — longer-termCumulative external dose is usually low for ordinary samples but may need assessment for unusual amounts or radioisotope-enriched materials.
Internal exposure — near-termNatural radionuclides may enter the body with dust, gases or soluble materials. Immediate radiologic symptoms are not expected at background-level intake; chemical toxicity may be separate. C-14-labelled CO2 or particulates can cause internal beta dose; risk depends on intake and metabolism.
Internal exposure — longer-termRadiation-induced effects depend on committed organ dose and retention, not merely the element name; higher intakes can increase long-term cancer risk.

Isotope mass-number inventory (reference registry; not complete ENSDF): 15 recorded: 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22. • The nuclide examples are selected reference entries from Volume 1, not an evaluated inventory of every isotope. Original half-life/status data require current nuclear-database checks. Distance alone cannot establish a safe dose.

04
Separate exposure routes

Human effects & chemical reactions

The colored chips are inherited qualitative editorial screening labels, not GHS classifications, measured dose thresholds or permissions to touch or breathe any substance.

Skin contact & inhalation

Route & durationScreeningPossible effectsConditions
Skin contact — immediateVery lowBrief touch of intact graphite/diamond usually has no toxic effect; powders can dry or irritate the skin.Route-specific interpretation only; form, concentration and duration still matter.
Skin contact — repeatedVery lowDryness or irritation can occur with repeated carbon powders; intact graphite or diamond has little dermal toxicity.Route-specific interpretation only; form, concentration and duration still matter.
Inhalation — immediateModerateGraphite/carbon-black dust may irritate airways; bulk diamond or graphite is not inhalable.Route-specific interpretation only; form, concentration and duration still matter.
Inhalation — repeatedHighHigh sustained respirable exposures to some carbon dusts may impair lungs; risk differs by carbon allotrope and impurities.Route-specific interpretation only; form, concentration and duration still matter.

Air & water

ExposureScreeningReaction & effectInterpretation
Air, oxygen and humidityHighGraphite/diamond are stable in ordinary air; burning carbon forms CO2 and, with incomplete combustion, CO; carbon dust is combustible.Interpret together with storage, ignition and process conditions.
Water contactVery lowNo ordinary chemical reaction with water; carbon materials may adsorb water or disperse as powder.Interpret together with storage, ignition and process conditions.
05
Beyond direct exposure

Twelve additional hazard pathways

Ingestion, ocular contact, pressure, fire, heat, incompatibilities, bioaccumulation and other relevant laboratory pathways.

HazardScreeningPossible effectPractical context
IngestionLowA small accidental amount of clean bulk material is not expected to cause characteristic acute chemical poisoning; particles can still obstruct, irritate or cause choking.Do not allow ingestion; wash hands and separate food from lab work. CONDITION: Not evidence that the element is edible.
Eye exposureModerateSolid fragments, dust or filings can abrade or irritate eyes; no evidence of an ordinary corrosive effect from intact clean bulk metal.Keep material enclosed; use splash/impact-rated eyewear when processing. CONDITION: Physical injury is not the same as systemic toxicity.
Skin absorptionLowNo established substantial systemic absorption through intact skin for clean bulk elemental sample; contamination or damaged skin can change exposure.Basic gloves/hygiene and no intentional skin contact. CONDITION: Low skin uptake does not prove overall harmlessness.
Fire and explosionHighSome elemental forms burn in air (carbon dust/soot or sulfur); dispersed dust can increase fire hazard.Keep powders away from ignition; control dust and oxidizers. CONDITION: Diamond/graphite/sulfur allotropes and forms differ.
Heating and fumesModerateHeating any element can cause thermal burns; hot particulates, evolved vapor or reaction products may alter toxicity.Determine melting/boiling points and fume chemistry; use local exhaust and thermal PPE. CONDITION: No claim that cold metal produces these fumes.
Chemical incompatibilityModerateStrong acids, bases, oxidizers or halogens may corrode or transform elemental material; the reaction must be checked case by case.Verify exact pairwise compatibility and expected evolved gases before mixing. CONDITION: Not a general permission to mix.
Storage and pressureLowA closed clean bulk elemental solid ordinarily has modest storage hazard, but broken glass, bad labeling and cross-contamination remain possible.Use compatible labeled, mechanically protected container and segregate reagents. CONDITION: Not an assertion that every compound of this element is safe.
BioaccumulationUncertainNo reliable general claim about long-term tissue accumulation can be made for every form of this element.Check chemical species, particulate size, bioavailability and toxicokinetics. CONDITION: Absence of evidence is not evidence of no retention.
Reproductive/developmental effectsUncertainInsufficient elemental-form evidence to classify reproductive/developmental toxicity for ordinary laboratory handling.Consult verified CLP/GHS classification and specific SDS; do not substitute metal-compound studies. CONDITION: Unknown is grey, not green.
Environmental effectsModerateEnvironmental hazard depends on weathering, particle size, soluble products and ecosystem exposure; elemental identity alone is insufficient.Collect metal residues and avoid uncontrolled discharge; consult local waste classification. CONDITION: Conservative screening.
Cryogenic effectsLowElement does not ordinarily require cryogenic containment; any object chilled sufficiently can cause frostbite and sealed vessels can fail thermally.Use cryogenic PPE and compatible temperature-rated apparatus only if process actually uses low temperature. CONDITION: No intrinsic hazard at room temperature.
Mechanical and pressure hazardsModerateCrystalline or brittle pieces can fracture into sharp fragments; processing produces particulate.Cut/cleave behind guards; avoid dust and chips. CONDITION: Form-dependent; diamond is hard, graphite soft.
06
From questions to evidence

Experimental program

Candidate investigation plans requiring qualified supervision and method-specific review before laboratory use.

Laboratory access tierSchool observation to professional testing — Handling only if local assessment deems the chosen form, quantity and method appropriate.
Research objectiveMeasure graphite versus other carbon-allotrope electrical behavior
Expected observation / outputResistivity, Raman D/G signals. Predetermine units, calibration basis and appropriate control.
Available physical formDocument exact allotrope, crystalline/amorphous phase, dopant level and surface finish.
Sample preparation & apparatusClean tools, substrate/sample fixture, four-probe/Raman/XRD as appropriate; manage surface contamination.
Atmosphere and compatibilitySpecify air/humidity or controlled atmosphere explicitly; record oxygen, moisture and exposure time if surface changes matter.
Production / refining contextOccurrence/production context: Coal, hydrocarbons, biomass; high-purity graphite and synthetic diamond produced industrially. Compare supply grade, supplier CoA and measured composition before choosing a refining route.
Reaction, oxidation & corrosionDiamond, graphite, graphene, amorphous carbon and nanotubes differ drastically in bonding and properties. For a reaction or corrosion claim, state the exact phase, reagent, concentration, surface finish and time; compare blank/control.
Temperature, pressure & phaseSelect temperature/pressure only after phase and hazard review; do not assume handbook values for unknown allotropes.
Electrical / magnetic / optical measurementRaman spectroscopy for allotropes/defects; combustion analysis for carbon content. Confirm the method measures the actual specified elemental form; several listed techniques characterize derivatives or compounds.
Quantification & verificationNever infer properties from 'carbon' alone: allotrope, morphology and defects control performance. Record lot/CoA, preparation, blanks, calibration, replicate results, uncertainty and waste disposition.
Important experimental pitfallAllotrope and defect content dominate measured properties.
Teaching / research levelsSchool: teacher-approved observation or safe comparison. University: quantitative method with controls. Research: advanced instrument and uncertainty study.
Preservation & data archiveUse labeled chemically compatible sealed storage; document surface condition, humidity, atmosphere and any change since measurement.
07
See the science

Element video

Video coming soon

A general YouTube video for this element can be added in the administration dashboard.

08
Reproducible work

Measurement & verification

Choose a method appropriate to the specimen and measurand, then document calibration, controls, uncertainty and interpretation limits.

Experimental access / responsibilityT1/T2 • supervised accessible specimen when form-specific risk assessment permits
Practical experiment questionMeasure graphite versus other carbon-allotrope electrical behavior.
Measurable evidenceResistivity, Raman D/G signals. Carbon allotrope/phase; defect proxies, not total elemental purity.
Measurement pathway (candidate)Raman plus XRD for certified carbon specimen.
Specimen & interpretation boundaryAllotrope and defect content dominate measured properties.
Known failure/false conclusionDifferent allotropes, laser heating, fluorescence and impurity-derived peaks.
Evidence required BEFORE useNIST structural reference standards + property-specific method report [R10,R17].
Important limitationA suggested technique is not a validated SOP. Verify exact specimen, measurand, method scope, calibration, blanks, control materials, uncertainty, operator competence and applicable institutional approvals before work.
NoteNitrogen
09
Evidence and revision

Sources & editorial status

Scientific review pending

Imported from the prepublication chemistry manuscript. Claim-level scientific review and direct source mapping are not complete. Do not rely on the screening assessments for laboratory safety decisions.

Review: · Last checked: