ELEMENT 014 / METALLOID
14SiATOMIC NUMBER · SYMBOL

Silicon

Experimental chemistry • properties • laboratory science

Network covalent semiconductor; Si(IV) oxides and silicates; controlled doping changes conductivity.

Atomic no. 14MetalloidSolid at room conditions
Explore profile
IMAGE PLACEHOLDERSiReal element images to be added later

Click a photograph for a larger view. Images are managed in the editor.

01
The essentials

Overview & practical chemistry

Identity, occurrence, applications and measurement context from the working reference manuscript.

Atomic number14
Symbol / typeSi · Metalloid • Solid at room temperature • atomic mass: 28.086 (rounded)
Elemental formSolid | selected oxidation states -4,+4
Chemical identityNetwork covalent semiconductor; Si(IV) oxides and silicates; controlled doping changes conductivity.
Occurrence and productionQuartz/silica reduced in furnaces; electronic grade by chlorosilane purification/zone refining.
Useful applicationsMicrochips, solar cells, silicones (compounds) and glass.
Analytical characterizationFour-point probe/resistivity; SIMS for dopants; Raman/XRD for crystallinity.
Research / quality noteSingle crystal, polysilicon, amorphous Si and silica are not interchangeable.
Bench propertiesApprox. melting 1414 °C; density 2.33 g/cm³ near room temperature. Check phase/purity before design.
Oxidation and chemical formsSelected: -4 / +4. Values depend on compound and chemical environment.

Phase transitions & temperature reference

Elemental bulk · approximately 1 atm

At approximately 1 atm, bulk values depend on specimen, isotope mixture and phase. When specific measurements or published theoretical estimates exist, they are labeled. A value borrowed from a normal element is only a reference proxy. Plasma is an ionized state, without a single universal onset temperature.

Phase at 20 °C, ~1 atmSolid
Elemental-bulk melting / freezing (near 1 atm)1688 K (1414.85 °C)
Elemental-bulk boiling / gas formation (near 1 atm)3538 K (3264.85 °C)
Sublimation (solid → gas) near 1 atmNot the stable direct phase boundary at 1 atm (melting then boiling)
Additional solid–solid transitions?
Plasma onset temperatureNot a single phase boundary; ionization is density/pressure/energy dependent
Measurement conditionsca. 1 atm; evaluated elemental-bulk reference only
Data qualificationNIST evaluated elemental-bulk solid–liquid transition; verify sample form and pressure.

Solid-phase reference: NIST Technical Note 2312 (2025). Boiling data: PubChem (NIH) where checked, otherwise secondary tabulation (provisional). Additional tabulated elemental values were cross-checked with the Royal Society of Chemistry. Where one exists, the named-form reference is not a universally applicable transition. Values can be form-dependent, metastable, estimated or pressure-dependent; verify against original reports for laboratory use.

02
Structure matters

Allotropes & elemental forms

Values are distinguished as form-specific measurements, theoretical predictions, or ELEMENTAL REFERENCE proxies. A numerical proxy describes the natural-element reference, not a measured melting/boiling point of that named form. ? remains where no defensible value or proxy exists.

Form / phaseState at 20 °CMelting / transitionBoiling / sublimation
Si-I / diamond-cubic silicon (3C-Si)Solid (elemental baseline; named form stability can differ)≈1688 K(1414.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)≈3538 K(3264.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)
Full record, evidence, conditions & photographs
Structure, conditions & interpretation
Ordinary tetrahedral cubic crystal; standard electronics-grade silicon. LAB: XRD lattice and Raman about 520 cm−1 are common identifiers.
Approximate solid / liquid / gas ranges
Bulk/form-comparator melting ~1688 K; generic gas reference ~3538 K. NOT a phase range for this named form; it can transform or exist only under special pressure.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Phase conditions
~1 atm elemental baseline. This particular structural form can transform, sublime or decompose before the listed bulk transition.
Evidence level
ELEMENTAL/OTHER-FORM REFERENCE only — NOT this form’s measurement
Phase data source
https://nvlpubs.nist.gov/nistpubs/TechnicalNotes/NIST.TN.2312.pdf
Photographs

No photograph added yet.

Si-II / β-tin-typeSolid (elemental baseline; named form stability can differ)≈1688 K(1414.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)≈3538 K(3264.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)
Full record, evidence, conditions & photographs
Structure, conditions & interpretation
High-pressure metallic tetragonal phase under compression. LAB: Reverts or changes during decompression; in-situ diffraction needed.
Approximate solid / liquid / gas ranges
Bulk/form-comparator melting ~1688 K; generic gas reference ~3538 K. NOT a phase range for this named form; it can transform or exist only under special pressure.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Phase conditions
~1 atm elemental baseline. This particular structural form can transform, sublime or decompose before the listed bulk transition.
Evidence level
ELEMENTAL/OTHER-FORM REFERENCE only — NOT this form’s measurement
Phase data source
https://nvlpubs.nist.gov/nistpubs/TechnicalNotes/NIST.TN.2312.pdf
Photographs

No photograph added yet.

Si-III (BC8) and Si-XII (R8)Solid (elemental baseline; named form stability can differ)≈1688 K(1414.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)≈3538 K(3264.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)
Full record, evidence, conditions & photographs
Structure, conditions & interpretation
Distinct recovered/metastable high-pressure structural families. LAB: Can affect electrical response after indentation; XRD/Raman verification.
Approximate solid / liquid / gas ranges
Bulk/form-comparator melting ~1688 K; generic gas reference ~3538 K. NOT a phase range for this named form; it can transform or exist only under special pressure.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Phase conditions
~1 atm elemental baseline. This particular structural form can transform, sublime or decompose before the listed bulk transition.
Evidence level
ELEMENTAL/OTHER-FORM REFERENCE only — NOT this form’s measurement
Phase data source
https://nvlpubs.nist.gov/nistpubs/TechnicalNotes/NIST.TN.2312.pdf
Photographs

No photograph added yet.

Si-IV / hexagonal-diamond (lonsdaleite-type), including 2H/6H polytypesSolid (elemental baseline; named form stability can differ)≈1688 K(1414.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)≈3538 K(3264.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)
Full record, evidence, conditions & photographs
Structure, conditions & interpretation
Hexagonally stacked crystalline structures produced by specialized routes. LAB: Distinguish polytype, stacking faults and phase purity rather than calling all “hexagonal silicon.”
Approximate solid / liquid / gas ranges
Bulk/form-comparator melting ~1688 K; generic gas reference ~3538 K. NOT a phase range for this named form; it can transform or exist only under special pressure.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Phase conditions
~1 atm elemental baseline. This particular structural form can transform, sublime or decompose before the listed bulk transition.
Evidence level
ELEMENTAL/OTHER-FORM REFERENCE only — NOT this form’s measurement
Phase data source
https://nvlpubs.nist.gov/nistpubs/TechnicalNotes/NIST.TN.2312.pdf
Photographs

No photograph added yet.

Si-IX (ST12), Si-V and other compressed phasesSolid (elemental baseline; named form stability can differ)≈1688 K(1414.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)≈3538 K(3264.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)
Full record, evidence, conditions & photographs
Structure, conditions & interpretation
Reported tetragonal, simple-hexagonal and other pressure-field structures. LAB: The numbered Si phase registry is larger than this practical table; cite exact study.
Approximate solid / liquid / gas ranges
Bulk/form-comparator melting ~1688 K; generic gas reference ~3538 K. NOT a phase range for this named form; it can transform or exist only under special pressure.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Phase conditions
~1 atm elemental baseline. This particular structural form can transform, sublime or decompose before the listed bulk transition.
Evidence level
ELEMENTAL/OTHER-FORM REFERENCE only — NOT this form’s measurement
Phase data source
https://nvlpubs.nist.gov/nistpubs/TechnicalNotes/NIST.TN.2312.pdf
Photographs

No photograph added yet.

Silicon clathrates / open-framework elemental SiSolid (elemental baseline; named form stability can differ)≈1688 K(1414.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)≈3538 K(3264.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)
Full record, evidence, conditions & photographs
Structure, conditions & interpretation
Host-free Si136 and related cages can be metastable after precursor removal. LAB: Ensure no alkali metal remains before claiming pure elemental Si. [AL8]
Approximate solid / liquid / gas ranges
Bulk/form-comparator melting ~1688 K; generic gas reference ~3538 K. NOT a phase range for this named form; it can transform or exist only under special pressure.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Phase conditions
~1 atm elemental baseline. This particular structural form can transform, sublime or decompose before the listed bulk transition.
Evidence level
ELEMENTAL/OTHER-FORM REFERENCE only — NOT this form’s measurement
Phase data source
https://nvlpubs.nist.gov/nistpubs/TechnicalNotes/NIST.TN.2312.pdf
Photographs

No photograph added yet.

Identification and structural context
OverviewAllotropy describes structurally different forms made of the same element. Distinguish genuine allotropes from melting/freezing, impurities, compounds, isotopes, size-dependent surface effects and magnetic transitions. “Normal” below means approximately 1 atm unless another pressure is stated.
Transition noteNo additional independently evaluated ordinary-pressure solid–solid transition temperature is listed here. Absence of a table entry does not prove that no pressure-induced or metastable phases exist.
Laboratory identificationLaboratory identification: use phase-specific powder/single-crystal XRD, Raman or other appropriate spectroscopy, with documented temperature, pressure, composition, impurities, substrate and thermal history. A color or appearance alone is insufficient.
Evidence & scopeEvidence & scope: [AL8]. Lists cover established principal named forms and notable experimentally reported polymorphs; an absolutely exhaustive list of all high-pressure, ultrathin, transient, metastable or newly discovered structures is not scientifically fixed. If data are unavailable, this is recorded rather than invented.
03
Nuclear science

Selected isotopes & radioactivity

This is a selected isotope list, not all known nuclides. Exact isotope-specific results are used where documented; elsewhere numerical elemental references are shown only as proxies, never as measurements or calculated isotope-specific estimates. Very short-lived isotopes cannot practically be collected in bulk. Plasma has no universal onset temperature.

NuclideHalf-lifeState at 20 °CMelting / transitionBoiling / sublimation
Si-28Stable; no observed radioactive decaySolid (expected elemental chemical form, not isotope-specific observation)≈1688 K(1414.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)≈3538 K(3264.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)
Full record, evidence, conditions & photographs
Decay or evidence note
Stable nuclide; verify current NNDC evaluation
Approximate solid / liquid / gas ranges
Elemental-reference ranges ONLY, not proven for this isotope at ~1 atm: solid below ~1688 K; liquid between ~1688 and ~3538 K; gas above ~3538 K. Not a plasma threshold.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Pressure / sample conditions
Pure isotope values can differ from natural-element mixture; ~1 atm reference; the elemental form and isotopic enrichment must be specified.
Evidence level
ELEMENTAL/FORM REFERENCE only — NOT an isotope measurement
Isotope phase source
https://nvlpubs.nist.gov/nistpubs/TechnicalNotes/NIST.TN.2312.pdf
Photographs

No photograph added yet.

Si-29Stable; no observed radioactive decaySolid (expected elemental chemical form, not isotope-specific observation)≈1688 K(1414.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)≈3538 K(3264.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)
Full record, evidence, conditions & photographs
Decay or evidence note
Stable nuclide; verify current NNDC evaluation
Approximate solid / liquid / gas ranges
Elemental-reference ranges ONLY, not proven for this isotope at ~1 atm: solid below ~1688 K; liquid between ~1688 and ~3538 K; gas above ~3538 K. Not a plasma threshold.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Pressure / sample conditions
Pure isotope values can differ from natural-element mixture; ~1 atm reference; the elemental form and isotopic enrichment must be specified.
Evidence level
ELEMENTAL/FORM REFERENCE only — NOT an isotope measurement
Isotope phase source
https://nvlpubs.nist.gov/nistpubs/TechnicalNotes/NIST.TN.2312.pdf
Photographs

No photograph added yet.

Si-30Stable; no observed radioactive decaySolid (expected elemental chemical form, not isotope-specific observation)≈1688 K(1414.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)≈3538 K(3264.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)
Full record, evidence, conditions & photographs
Decay or evidence note
Stable nuclide; verify current NNDC evaluation
Approximate solid / liquid / gas ranges
Elemental-reference ranges ONLY, not proven for this isotope at ~1 atm: solid below ~1688 K; liquid between ~1688 and ~3538 K; gas above ~3538 K. Not a plasma threshold.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Pressure / sample conditions
Pure isotope values can differ from natural-element mixture; ~1 atm reference; the elemental form and isotopic enrichment must be specified.
Evidence level
ELEMENTAL/FORM REFERENCE only — NOT an isotope measurement
Isotope phase source
https://nvlpubs.nist.gov/nistpubs/TechnicalNotes/NIST.TN.2312.pdf
Photographs

No photograph added yet.

Si-32153 ySolid (expected elemental chemical form, not isotope-specific observation)≈1688 K(1414.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)≈3538 K(3264.85 °C) (elemental-reference proxy, NOT specific to this isotope/form)
Full record, evidence, conditions & photographs
Decay or evidence note
beta-
Approximate solid / liquid / gas ranges
Elemental-reference ranges ONLY, not proven for this isotope at ~1 atm: solid below ~1688 K; liquid between ~1688 and ~3538 K; gas above ~3538 K. Not a plasma threshold.
Plasma onset
Not a fixed temperature — ionization depends on density, pressure and energy input
Pressure / sample conditions
Pure isotope values can differ from natural-element mixture; ~1 atm reference; the elemental form and isotopic enrichment must be specified.
Evidence level
ELEMENTAL/FORM REFERENCE only — NOT an isotope measurement
Isotope phase source
https://nvlpubs.nist.gov/nistpubs/TechnicalNotes/NIST.TN.2312.pdf
Photographs

No photograph added yet.

Radiological exposure & interpretation
Isotope basisCommon elemental specimens include stable isotopes; example *radioactive* isotope: Si-32. The BLUE entries refer ONLY to stable nuclides, not to Si-32.
External radiation — near-termStable nuclides emit no nuclear decay radiation; no direct radiological injury from brief contact with the stable-only material. Radioisotope-labelled material is a different case.
External radiation — longer-termStable-only material causes no cumulative ionizing dose from its own nuclei. For a radioactive isotope, long-term effects depend on measured dose; cancer risk can increase.
Internal exposure — near-termStable-only particles/gases give no internal radionuclide dose. Chemical or asphyxiation risks still apply. A radioactive isotope taken into the body can deliver organ dose.
Internal exposure — longer-termStable-only material has no radiation-driven long-term effect. Inhaled radioisotopes may be retained and increase delayed cancer risk; isotope and chemical form govern the outcome.

Isotope mass-number inventory (reference registry; not complete ENSDF): 23 recorded: 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44. • The nuclide examples are selected reference entries from Volume 1, not an evaluated inventory of every isotope. Original half-life/status data require current nuclear-database checks. Distance alone cannot establish a safe dose.

04
Separate exposure routes

Human effects & chemical reactions

The colored chips are inherited qualitative editorial screening labels, not GHS classifications, measured dose thresholds or permissions to touch or breathe any substance.

Skin contact & inhalation

Route & durationScreeningPossible effectsConditions
Skin contact — immediateVery lowBulk usually low acute skin hazard.Route-specific interpretation only; form, concentration and duration still matter.
Skin contact — repeatedVery lowRepeated handling of silicon pieces usually causes little dermal effect except abrasion.Route-specific interpretation only; form, concentration and duration still matter.
Inhalation — immediateModerateElemental silicon powder can irritate the airway; this is NOT the same as respirable crystalline silica (SiO2).Route-specific interpretation only; form, concentration and duration still matter.
Inhalation — repeatedHighChronic risk of elemental silicon dust is not equivalent to silicosis from crystalline silica; identify actual material.Route-specific interpretation only; form, concentration and duration still matter.

Air & water

ExposureScreeningReaction & effectInterpretation
Air, oxygen and humidityModerateSilicon forms a thin protective silica surface; high temperatures promote oxidation; silicon dust can burn.Interpret together with storage, ignition and process conditions.
Water contactVery lowCrystalline silicon does not normally react with cold water; strong alkali solutions are different.Interpret together with storage, ignition and process conditions.
05
Beyond direct exposure

Twelve additional hazard pathways

Ingestion, ocular contact, pressure, fire, heat, incompatibilities, bioaccumulation and other relevant laboratory pathways.

HazardScreeningPossible effectPractical context
IngestionLowA small accidental amount of clean bulk material is not expected to cause characteristic acute chemical poisoning; particles can still obstruct, irritate or cause choking.Do not allow ingestion; wash hands and separate food from lab work. CONDITION: Not evidence that the element is edible.
Eye exposureModerateSolid fragments, dust or filings can abrade or irritate eyes; no evidence of an ordinary corrosive effect from intact clean bulk metal.Keep material enclosed; use splash/impact-rated eyewear when processing. CONDITION: Physical injury is not the same as systemic toxicity.
Skin absorptionLowNo established substantial systemic absorption through intact skin for clean bulk elemental sample; contamination or damaged skin can change exposure.Basic gloves/hygiene and no intentional skin contact. CONDITION: Low skin uptake does not prove overall harmlessness.
Fire and explosionModerateFire behavior depends strongly on metal powders, temperature, oxygen enrichment or mixing with other chemicals.Check SDS and combustion data before heating or making fine powders. CONDITION: Conservative screening, not proof of combustibility.
Heating and fumesModerateHeating any element can cause thermal burns; hot particulates, evolved vapor or reaction products may alter toxicity.Determine melting/boiling points and fume chemistry; use local exhaust and thermal PPE. CONDITION: No claim that cold metal produces these fumes.
Chemical incompatibilityModerateStrong acids, bases, oxidizers or halogens may corrode or transform elemental material; the reaction must be checked case by case.Verify exact pairwise compatibility and expected evolved gases before mixing. CONDITION: Not a general permission to mix.
Storage and pressureLowA closed clean bulk elemental solid ordinarily has modest storage hazard, but broken glass, bad labeling and cross-contamination remain possible.Use compatible labeled, mechanically protected container and segregate reagents. CONDITION: Not an assertion that every compound of this element is safe.
BioaccumulationUncertainNo reliable general claim about long-term tissue accumulation can be made for every form of this element.Check chemical species, particulate size, bioavailability and toxicokinetics. CONDITION: Absence of evidence is not evidence of no retention.
Reproductive/developmental effectsUncertainInsufficient elemental-form evidence to classify reproductive/developmental toxicity for ordinary laboratory handling.Consult verified CLP/GHS classification and specific SDS; do not substitute metal-compound studies. CONDITION: Unknown is grey, not green.
Environmental effectsModerateEnvironmental hazard depends on weathering, particle size, soluble products and ecosystem exposure; elemental identity alone is insufficient.Collect metal residues and avoid uncontrolled discharge; consult local waste classification. CONDITION: Conservative screening.
Cryogenic effectsLowElement does not ordinarily require cryogenic containment; any object chilled sufficiently can cause frostbite and sealed vessels can fail thermally.Use cryogenic PPE and compatible temperature-rated apparatus only if process actually uses low temperature. CONDITION: No intrinsic hazard at room temperature.
Mechanical and pressure hazardsModerateCrystalline or brittle pieces can fracture into sharp fragments; processing produces particulate.Cut/cleave behind guards; avoid dust and chips. CONDITION: Form-dependent; diamond is hard, graphite soft.
06
From questions to evidence

Experimental program

Candidate investigation plans requiring qualified supervision and method-specific review before laboratory use.

Laboratory access tierSchool observation to professional testing — Handling only if local assessment deems the chosen form, quantity and method appropriate.
Research objectiveDetermine silicon crystal versus amorphous structure and carrier response
Expected observation / outputXRD/Raman and resistivity. Predetermine units, calibration basis and appropriate control.
Available physical formDocument exact allotrope, crystalline/amorphous phase, dopant level and surface finish.
Sample preparation & apparatusClean tools, substrate/sample fixture, four-probe/Raman/XRD as appropriate; manage surface contamination.
Atmosphere and compatibilitySpecify air/humidity or controlled atmosphere explicitly; record oxygen, moisture and exposure time if surface changes matter.
Production / refining contextOccurrence/production context: Quartz/silica reduced in furnaces; electronic grade by chlorosilane purification/zone refining. Compare supply grade, supplier CoA and measured composition before choosing a refining route.
Reaction, oxidation & corrosionNetwork covalent semiconductor; Si(IV) oxides and silicates; controlled doping changes conductivity. For a reaction or corrosion claim, state the exact phase, reagent, concentration, surface finish and time; compare blank/control.
Temperature, pressure & phaseScreening context: approx. melt 1414 °C and density 2.33 g/cm³ (from Volume 2; condition-dependent). Verify by DSC/density method only if justified.
Electrical / magnetic / optical measurementFour-point probe/resistivity; SIMS for dopants; Raman/XRD for crystallinity. Confirm the method measures the actual specified elemental form; several listed techniques characterize derivatives or compounds.
Quantification & verificationSingle crystal, polysilicon, amorphous Si and silica are not interchangeable. Record lot/CoA, preparation, blanks, calibration, replicate results, uncertainty and waste disposition.
Important experimental pitfallDoping and oxide layers alter results dramatically.
Teaching / research levelsSchool: teacher-approved observation or safe comparison. University: quantitative method with controls. Research: advanced instrument and uncertainty study.
Preservation & data archiveUse labeled chemically compatible sealed storage; document surface condition, humidity, atmosphere and any change since measurement.
07
See the science

Element video

Video coming soon

A general YouTube video for this element can be added in the administration dashboard.

08
Reproducible work

Measurement & verification

Choose a method appropriate to the specimen and measurand, then document calibration, controls, uncertainty and interpretation limits.

Experimental access / responsibilityT1/T2 • supervised accessible specimen when form-specific risk assessment permits
Practical experiment questionDetermine silicon crystal versus amorphous structure and carrier response.
Measurable evidenceXRD/Raman and resistivity. Crystal structure and electrical behavior.
Measurement pathway (candidate)Raman/XRD, then electrical resistivity if relevant.
Specimen & interpretation boundaryDoping and oxide layers alter results dramatically.
Known failure/false conclusionDopants, oxygenated surface, defects, wafer geometry and electrical contact resistance.
Evidence required BEFORE useNIST structural reference standards + property-specific method report [R10,R17].
Important limitationA suggested technique is not a validated SOP. Verify exact specimen, measurand, method scope, calibration, blanks, control materials, uncertainty, operator competence and applicable institutional approvals before work.
NotePhosphorus
09
Evidence and revision

Sources & editorial status

Scientific review pending

Imported from the prepublication chemistry manuscript. Claim-level scientific review and direct source mapping are not complete. Do not rely on the screening assessments for laboratory safety decisions.

Review: · Last checked: